Program Auto1 Auto2 Description Program that runs on a predetermined time interval that is fixed. Program that runs on a predetermined time interval that is fixed. Custom User-programmable scene, which can be programmed by following the instructions on page Up to 32 fixtures may be linked together in this mode. Edit Program 2 Scroll through to the step you wish to program, and select it. Scroll through to the pan value you wish to program, and select it.
Tilt Red Green Blue The program runs in sequential order, starting with step , and continuing through the last step that was programmed. It is therefore not necessary to program all steps. In other words, if only steps , , and are programmed, the routine will start again at step after step has finished executing. The program can be run in any mode.
See the above instructions for the desired operating mode in order to run the custom program. For example, if time is set to 4, fade can be This section details how to change the fan speed, invert the Pan, invert the Tilt, reset the fixture, and restore the fixture to factory default settings. The fixture will then reset itself.
This will restore all settings to their factory defaults. Channels may be assigned in any manner. A fixture capable of receiving DMX will require one or a number of sequential channels. The user must assign a starting address on the fixture that indicates the first channel reserved in the controller. There are many different types of DMX controllable fixtures and they all may vary in the total number of channels required.
Choosing a start address should be planned in advance. Channels should never overlap. If they do, this will result in erratic operation of the fixtures whose starting address is set incorrectly.
You can however, control multiple fixtures of the same type using the same starting address as long as the intended result is that of unison movement or operation.
In other words, the fixtures will be slaved together and all respond exactly the same. DMX fixtures are designed to receive data through a serial Daisy Chain. The order in which the fixtures are connected is not important and has no effect on how a controller communicates to each fixture. Use an order that provides for the easiest and most direct cabling. Connect fixtures using shielded two conductor twisted pair cable with three pin XLR male to female connectors. Contact the nearest Chauvet dealer to order any of these cables.
Maintenance To maintain optimum performance and minimize wear, fixtures should be cleaned frequently. Usage and environment are contributing factors in determining frequency. As a general rule, fixtures should be cleaned at least twice a month.
Dust build up reduces light output performance and can cause overheating. This can lead to reduced lamp life and increased mechanical wear. Be sure to power off fixture before conducting maintenance. Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust collected on external vents and internal components. Clean all glass when the fixture is cold with a mild solution of glass cleaner or Isopropyl Alcohol and a soft lint-free cotton cloth or lens tissue.
Apply solution to the cloth or tissue and drag dirt and grime to the outside of the lens. ONLY connect this product to a grounded and protected circuit.
The product consists of a base and a moving head on a yoke. The LEDs are inside ducts, which, along with special optics, provide a very narrow beam angle. Fuse 1. Disconnect this product from the power outlet. Replacement 2. Wedge the tip of a flat head screwdriver into the slot of the fuse holder.
Pry the safety cap out of its housing to pull out the installed fuse. Remove the blown fuse from its safety cap and replace it with a fuse of the exact same type and rating F 3. A — FAX www. Page 2: Table Of Contents To restore all settings to their factory defaults The factory will not allow any shipments without an RMA. Page 7: Setup You must supply your own clamp and make sure the clamp is capable of supporting the weight of this fixture.
Block access below the work area and use suitable and stable platform when installing or servicing fixture. Page 8: Fixture Linking Maximum recommended number of fixtures on a serial data link: 32 fixtures Data Cabling To link fixtures together you must obtain data cables.
If you choose to create your own cable please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference. Then, proceed to connect from the output as stated above to the input of the following fixture and so on.
Page Operating Instructions 4. Up to 32 fixtures may be Menu linked together in this mode. Page Additional Menu Options Additional Menu Options This fixture can be customized in several different ways at the discretion of the user. This section details how to change the fan speed, invert the Pan, invert the Tilt, reset the fixture, and restore the fixture to factory default settings. Page Appendix XLR male to female connectors.
0コメント